Artificial Turf Installation Burbank
When you have completed the preparation stage which includes measuring how much artificial grass you require, installing appropriate drainage (if needed) and removing the natural grass layer, you will be prepared to install your artificial grass lawn. This post outlines the steps you should follow to help you to do the job right, from laying the base, connecting joints and preventing weed growth.
Lay Gravel Base accompanied by Sharp Sand – If required, use treated timber/timber stakes to put within an area frame. We recommend 4 X 2 inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and two X 2 inches of tantalised timber once and for all draining areas. Screw these timbers towards the stakes leaving the stakes on the inside of the perimeter. Should the Artificial Grass meet a concrete path, wall or decking, position the timber flush with all the surface height and by using 10mm temporary fillet, pack the timber close to the wall leaving the room to help you tuck the Artificial Grass in between the timber as well as the adjoining material in a later stage.
Position the stakes from the inner perimeter timber edging and hammer in to the ground ensuring the stakes are slightly below the timber edging. Next screw the timber stake to the timber edging. With heavy clay soils we recommend laying a crushed stone surface as much as 3 inches. This will not be necessary for the majority of areas and just required if you have a very high water table in which the ground holds water for a long period of time after it rains. Next compact the floor employing a vibrating plate that can be hired from an equipment hire company. Guarantee the perimeter is compacted and beneath the timber edging by 1 inch. Infill the perimeter with sharp sand and level using a rake. Guarantee the sand is level to the very top of the timber edging and compact again.
Permanently drainage areas spread a layer of sharp sand to blind on the soil. Next compact the floor employing a vibrating plate which can be hired from an equipment hire company. Guarantee the perimeter is compacted and level with all the timber edging. Should you put more function in at this time, your Artificial Grass Lawn can look better because of this.
Weed Control Layer – Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 inch galvanised clout nails for the timber edging. This weed control geo textile membrane prevents any probability of weed growth from the artificial grass drainage holes.
Roll out Artificial Grass – Lay the Artificial Grass in the desired direction working on the carpet rather than on the levelled base. Ensure the carpet is positioned to minimise cuts, joints and waste overlaying the timber edging by at least 4 inches. In the event the artificial grass meets a path or edge, and if you have laid the timber edging correctly as previously described, then this artificial grass could be wedged between. If joining, please be sure that the artificial grass is laid with the pile running inside the same direction on each piece. Lay the carpet on top of the sand instead of dragging it across the base material. To assist stop wrinkles or creasing it is advisable to allow 2 to three hours to settle before continuing with jointing and adhesive. Cut grass to shape employing a sharp Dolphin or Stanley knife or scissors.
Jointing – When jointing your outdoor carpet together, make sure the pile runs in the same direction. Stop manufacturer’s edge strip (if present) and butt two edges together ensuring you can find no gaps in excess of 1mm between the two carpet edges. The accuracy with this will determine how visible the join is after the completion. Fold back edges and position jointing tape (smooth side down) so the edges in the carpet meet the tape when joined.
Adhesive – a) Apply the cartridge adhesive in a zig zag motion on the rougher side in the tape allowing one cartridge for every 3 linear metres. Reject carpet and press both edges into the wet adhesive, ensuring every piece marries up and has no overlap. As you are doing this with your fingers, mix the fibres together to conceal the join. When the whole length is in place and you also are pleased using its appearance it really is necessary to walk across the join many times to activate the glue and bond the grass to the tape. Weigh down the seam to make sure good contact with the glue until it cures. The greater care taken with all the operation the neater and tidier the joint will likely be.
b) If utilizing the 2-component multi-purpose adhesive, ensure thorough mixing of these two components before use. Apply adhesive to the rough side of the tape and spread evenly across a width of at least 20cm using if possible a notched trowel. Sufficient adhesive should be applied so that when the artificial grass carpet is pressed in to the adhesive, a transfer over the carpet backing is finished. Reject carpet and press both edges into the wet adhesive, ensuring every piece marries up and has no overlap. Make sure the carpet will not crest on the seam and it is holding flat within the bonded area. Once the whole length is within place and you also are happy using its appearance it is necessary to walk over the join repeatedly to activate the glue and bond the grass to the tape. Weight the seam to ensure good connection with the glue until it cures. The more care taken using the operation the neater and tidier the joint is going to be.
As you should endeavour never to put adhesive to the carpet small quantities of glue can be taken off from your artificial grass fibre using White Spirit and a small off cut of the artificial grass. Small quantities of cured glue usually can be removed. To prevent this situation and the chance of damage to the artificial grass, care and precautions should be delivered to avoid vhhfqr with the fibres at all times. Once the artificial grass has become jointed and glued and you also are satisfied with all the levels screw the grass for the timber perimeter framework using galvanised screws at the very least of 12 inch intervals.
Spread Sand (Optional, based on Grass Selected) – If the artificial grass has been laid use silica sand, which is kiln dried and brush into carpet as you go. Each product may have sand infill but this can be only employed to stabilise the carpet as well as at virtually no time if the sand be visible. You must obtain an even spread on the surface using a brush to formulate the depth in layers. Usually do not apply the sand in a single application. Brush sand into pile soon after laying as the artificial grass is dry even though weather conditions are good. Brush vigorously up against the fibres in the carpet pile to let the tufts to stand upright. Putting the right level of sand in helps hold the artificial grass to bed down, protects the fibres and in addition keeps them standing allow it the look of real grass.